2.4.15
Sink, Service, Disposal, Flushing Rim (Item P6300)
Vitreous china pedestal type, 510 by 510 mm 20 by 20 inches, with flushing
rim and siphon jet flushing action. Service sink shall have a 40 mm 1 1/2
inch top inlet spud and a minimum rim to floor height of 460 mm 18 inches,
with stainless steel rim guards on front and both sides, and elongated
open-front seat, and ANSI large diaphragm (not less than 66.70 mm 2.625
inches upper chamber inside diameter at the point where the diaphragm is
sealed between the upper and lower chambers), nonhold open flush valve of
chrome plated copper alloy, including vacuum breaker and angle
(control-stop) valve with back check.
2.4.16
Sink, Service, Disposal, Flushing Rim (Item P6350)
Vitreous china, wall mounted, service sink with flushing rim and blowout
flushing action, 560 mm 22 inches wide, 660 mm 26 inches long, 270 mm 10
1/2 inches deep, and integral 120 mm 4 3/4 inches high, with elongated
open-front seat, and ANSI large diaphragm (not less than 66.70 mm 2.625
inches upper chamber inside diameter at the point where the diaphragm is
sealed between the upper and lower chambers), nonhold-open flush valve of
chrome plated copper alloy, including vacuum breaker and angle
(control-stop) valve with back check, wall mounted combination faucet with
renewable seats, 150 mm 6 inch brass handles, plain end spout with bucket
hook, screwdriver stops, fork brace, and stainless steel rim guards on
front and both sides.
2.4.17
Sink, Surgeon's Scrub-Up (Item P6900)
Vitreous china, wall mounted scrub-up sink having overall dimensions of 760
mm 30 inches long by 560 mm 22 inches wide by 250 mm 10 inches deep with
integral back 150 mm 6 inches high. Provide with [knee control]
[self-closing foot control] mixing valve, gooseneck spout with 50 mm 2 inch
spray, 250 mm 10 inches above sink rim, perforated strainer, 40 mm 1 1/2
inch tailpiece, and 40 mm 1 1/2 inch cast brass P-trap with cleanout plug.
2.4.18
Scrub Station, Surgical, Automatic (Item P6990)
Wall mounted, 14 gage, Type 304, welded stainless steel scrub sink with
[2][3][4] automatic scrub stations. Provide each station with volume
regulator, thermostat controlled water temperature selector, solid state
electronic timer with automatically timed scrub period, gooseneck spout
with full arm wash/rinse spray, automatic water shut-off, built-in
detergent dispenser, foot controls, perforated strainer, 40 mm 1 1/2 inch
tailpieces, and 40 mm 1 1/2 inch cast brass P-trap. Plastic splash shields
shall be provided between scrub stations. Temperature controls and timing
devices shall be watertight and enclosed to prevent tampering. Provide 15
mm 1/2 inch lines with hot and cold water at a pressure between 138 kPa 345
kPa 20 psi 50 psi and 120 volt, 60 hertz, single phase power to an internal
2.4.19
Trap, Interceptor, Plaster (Item P7500)
Cast iron sediment interceptor with side inlet; sealed side outlet; bolted,
removable, gasketed cover; removable galvanized basket having lift bars;
cast-iron removable inlet baffle; removable bronze screens; and cleanout at
bottom for installation on floor or flush with floor.
SECTION 15411N
Page 10
Previous Page
